Calcmadeira: Software for Estimating Lumber Production

Authors

  • Thomaz Costa

  • Tiago Santos

  • Lucas Barbosa Ramos

  • Monica Campanha

cut pattern, log, saw, timber, wood

Abstract

One information that is generally not used but is still essential to the economic evaluation and wood yield of the sawmill production chain is the quantification of lumber a priori. The few applications that provide a solution to this problem work with one log at a time and generally use optimization techniques instead of cut pattern models. The software developed for this work uses trigonometric rules, applying the circumscribed square (block), longitudinal (or tangential), log rotation, and radial cut patterns to help a producer sell a tree not in cubic meters but as a function of the pieces obtained from trees. Six tests were performed using trees and individual logs. The comparison between the calculated and milled or drawing pieces was presented for each model. The total errors obtained were approximately 2% for priority pieces. The best accuracy for the number and volume of the lumber pieces was 2.2% and -5.4%, respectively, obtained with a 30o angle of the slab (waste wood) and 0.60 to the proportion of the radius parameters in the model that rotates the log. The total calculated and observed piece width distributions were statistically equal in the radial model. This application requires observation of the milling operation while monitoring parameters in a heterogeneous sample of wooden logs to obtain the best results.

Downloads

How to Cite

Calcmadeira: Software for Estimating Lumber Production. (2022). Global Journal of Science Frontier Research, 22(13), 5-21. https://www.journalofscience.org/index.php/GJSFR/article/view/103402

References

Anjos APN (2017) Yield of sawn wood from Eucalyptus species. 16, 26-32. https://doi.org/10.5965/223811711612017026

Associação (ABNT) (2002) NBR 14807/2002: lumberpieces: dimensions.

Baesler FF, Araya E, Ramis FJ, Sepúlveda JA (2004) The Use of Simulation and Design of Experiments for Productivity Improvement in the Sawmill Industry. 2, 1218-1221.

Dhb Binoti (2012) Computer systems applied to forest management. https://www.locus.ufv.br/bitstream/123456789/576/1/texto%20completo.pdf

A. Bonato, M. Rocha, Cgf Juizo, R. Klitzke (2017) Effect of sawing system and diameter classes on Araucaria angustifolia sawn wood yield. 24, 1-8. https://doi.org/10.1590/2179-8087.100414

Brazil (2016) Resolução CONAMA n. 474 de 06 de abril de 2016. https://www.in.gov.br/materia/-/asset_publis

Chichorro JF, Resende JLP, Leite HG (2003) Volume and taper equations to quantify wood multiproducts in Atlantic forest. 27, 799-809.

Costa TCC, Campanha MM, França LFM (2019) First validation of Calc Madeira software for estimating round and sawn wood pieces. 194, 1-24. https://ainfo.cnptia.embrapa.br/digital/bitstream/item/205878/1/bol-194.pdf

Tcc Costa, L. França, Thp Santos (2020) Second validation of Calc Madeira: Estimation of sawn pieces from empirical sawing. Embrapa, Sete Lagoas, Minas Gerais. 214, 1-31. https://ainfo.cnptia.embrapa.br/digital/bitstream/item/217846/1/Bol-214.pdf

Tcc Costa, M. Campanha, Gontijo Neto, M. (2016) Costa TCC, Campanha MM, Gontijo Neto MM. Quantification of round eucalyptus wood compared to valuation in cubic meter and firewood: income options in integrated crop-livestock-forest (iLPF) systems, Embrapa, Sete Lagoas, Minas Gerais. 224, 1-12. https://ainfo.cnptia.embrapa.br/digital/bitstream/item/158776/1/circ-224.pdf

A. Cunha, M. França, Ccf Almeida, L. Gorski, R. Cruz, D. Santos (2015) Yield evaluation of Eucalyptus benthamii and Eucalyptus grandis sawn wood using tangential and radial sawing. 45, 241-250.

Halabe UB, Gopalakrishnan B, Jadeja J (2011) Advanced lumber manufacturing model for increasing yield in sawmills using GPR-based defect detection system. 56, 649-661. https://doi.org/10.1007/s00170-011-3205-x

D. Heinrich (2010) Simulation of sawn wood production. https://www.lume.ufrgs.br/bitstream/handle/10183/21104/000737035.pdf?sequence=1

C. Juizo, M. Rocha, N. Bila (2014) Evaluation of eucalyptus lumber yield for two sawing models in a portable sawmill. 21, 543-550.

A. Kozak, D. Munro, Jgh Smith (1969) Taper Functions and their Application in Forest Inventory. 45(4), 278-283. https://doi.org/10.5558/tfc45278-4

H. Leite (1994) Conversion of logs into wood multiproducts, using dynamic programming, PhD, UFV, Minas Gerais, Brazil. https://www.locus.ufv.br/bitstream/123456789/26039/1/texto%20completo.pdf

LibreCAD (2020) https://librecad.org/

W. Lin, D. Kline, P. Araman, J. Wiedenbeck (1995) Design and evaluation of log - to - dimension manufacturing systems using system simulation. 45(3), 37-44.

Manhica AA, Rocha MP, Timofeiczyk R (2013) Eficiência operacional no desdobro de Pinus utilizando modelos de corte numa serraria de pequeno porte. 19(2), 339-346. https://doi.org/10.1590/s0104-77602013000200019

S. Maturana, E. Pizani, J. Vera (2010) Scheduling production for a sawmill: A comparison of a mathematical model versus a heuristic. 59, 667-674.

Murara Junior, M. Rocha, M. Trugilho, P. (2013) Yield estimation of pine sawn wood for two sawing methodologies. 20, 556-563. https://doi.org/10.4322/floram.2013.037

Gvp Nunes (2013) Algorithms for generating parallel and radial cutting patterns in the wood log process. 2. http://www.bibliotecaflorestal.ufv.br/bitstream/handle/123456789/5450/Dissertacao_Gilberto-Vinicius-Paulino-Nunes.pdf?sequence=1&isAllowed=y

E. Oliveira, M. Haliski, N. Nakajima, M. Chang (2011) Determining the amount of wood, carbon and financial gain from the forest plantation. 37. https://ainfo.cnptia.emb-rapa.br/digital/bitstream/item/40634/1/Doc220.pdf

E. Oliveira (2011) Software for management and economic analysis of forest plantations. 70. https://ainfo.cnptia.embrapa.br/digital/bitstream/item/39886/1/Doc216.pdf

(2020) OpTimber Available online: (). https://optimber.com.br/otimizacao-do-desdobro-de-toras

Pitago Optimizers (2020) https://pitago.eu/log-cut-en.php

M. Rocha, I. Tomaselli (2002) Effect of the sawing model on the quality of Eucalyptus grandis and Eucalyptus dunnii lumber. 8, 70-083.

F. Schumacher, F. Hall (1933) Logarithmic expression of timber-tree volume. 47, 719-734.

Serpe EL, Figueiredo A, Arce JE (2018) Yield of sawing wood in conventional sawmill and different simulations using computational optimizer. 3, 103. https://doi.org/10.5380/biofix.v3i1.58058

Soares TS, Vale AB, Leite HG, Machado CC (2003) Optimization of multiproducts in forest stands. 27, 811-820.

Philip Steele (1984) Factors determining lumber recovery in sawmilling. https://www.fpl.fs.fed.us/documnts/fplgtr/fplgtr39.pdf

TEKL STUDIO (2018) CultLog software. Detva. https://www.cutlog.com/index.php/downloads

(2020) Timber Vision Available online: vision. http://www.timbervision.fi/timberlog_en.html

Vergara FP, Palma CD, Sepulveda H (2015) A comparison of optimization models for lumber production planning. 36(2), 239-246. https://doi.org/10.4067/s0717-92002015000200009

Voronin A, Kuznetsov V, Arkhipov I, Shabaev A (2012) Software system for sawmill operation planning. 165-171. https://doi.org/10.23919/fruct.2012.8122101

Calcmadeira: Software for Estimating Lumber Production

Published

2022-05-06

How to Cite

Calcmadeira: Software for Estimating Lumber Production. (2022). Global Journal of Science Frontier Research, 22(13), 5-21. https://www.journalofscience.org/index.php/GJSFR/article/view/103402